AED Packages for Manufacturing Sites

Industrial AED packages built for production floors: high-visibility cabinets, rugged devices, and pads sized for the noise, dust and distance a factory setting actually presents.

90 dBA

OSHA's 8-hour noise limit

3 min

AHA response-time target

No exemption

Manufacturing is fully OSHA-covered

$149+

Free shipping threshold

Before you order a HeartSine unit Some HeartSine samaritan PAD devices are covered by an active Stryker recall. Check your serial number and read current guidance on our AED safety notices page.

Reviewed by Kyle Nowack, AHA BLS Instructor, Red Cross BLS Instructor Trainer, and AED Program Specialist. Meet Kyle Nowack

Planning coverage across multiple production lines or shifts? Call (855) 286-6384.

Defibtech Lifeline AED Church Value Package

Defibtech Lifeline AED Value Package

$1,523.00

In Stock.

(0)

Select Options

HeartSine samaritan PAD AED Value Package

$1,948.75

In Stock.

(0)

Select Options

ZOLL AED Plus Value Packages

$2,119.00

In Stock.

(0)

Select Options

Noise changes what "audible" means on a production floor

OSHA caps 8-hour noise exposure at 90 dBA. OSHA's own guidance notes that speech becomes hard to hear above roughly 85 dBA. Grinding, welding and machining operations routinely reach or exceed that range, with some measured as high as 108 to 115 dBA.

The device implication

A standard AED's voice prompts can be genuinely masked by ambient machinery noise at or near OSHA's own legal ceiling. Devices with visual guidance alongside audio prompts hold up better here than an audio-only design.

OSHA obligation: no exemption, unlike farms

General Duty Clause

Employers must provide a workplace free from recognized hazards likely to cause death or serious harm. No AED-specific mandate exists, but this clause remains a live exposure.

29 CFR 1910.151

Requires adequate first aid availability, and trained personnel where EMS is not in near proximity.

No small-facility carve-out

Unlike small farms, which carry a specific OSHA exemption, manufacturing facilities of any size are fully within general industry OSHA coverage.

This is not legal advice. Confirm any state-specific requirement directly.

How many AEDs your facility actually needs

The AHA's real published standard is a time target, not a square-footage formula: a device should be retrievable and a shock deliverable within roughly 3 minutes of collapse.

Industry planning sources translate that into rough coverage estimates ranging from about 20,000 to 100,000 sq ft per device, depending on layout and obstacles. That range is wide because it genuinely depends on your floor plan, not a single formula.

Scenario	Coverage note
Multi-level production areas	Additional device per floor or mezzanine level
Detached buildings, loading docks, yards	Each needs its own dedicated coverage, not reach from an indoor unit
Overnight or skeleton-crew shifts	Fewer staff spread across the same floor plate increases real response time
Highest-risk zones (production floor itself)	Prioritize over square-footage-even distribution

Call (855) 286-6384 with your floor plan and shift pattern for a specific placement recommendation.

What belongs in an industrial AED package

Rugged, dust and water-rated AED
High-visibility alarmed wall cabinet
Adult and pediatric-capable pad path
Spare battery and pad set
Rescue kit: gloves, razor, scissors, barrier mask
Clear facility signage
Physician's prescription, included

Full contents, warranty terms and running costs are on each product page: Defibtech Lifeline AED Value Package, HeartSine samaritan PAD AED Value Package, or ZOLL AED Plus Value Packages.

Frequently asked questions

Are AEDs required in manufacturing plants in the US?

No federal OSHA standard mandates AEDs specifically. The General Duty Clause and 29 CFR 1910.151 still apply, and some states impose their own requirements.

Manufacturing carries no exemption comparable to the small-farm carve-out; general industry coverage applies regardless of size.

What is the best AED for an industrial environment?

Prioritize a rugged, high IP-rated device with visual guidance alongside audio prompts, given documented factory-floor noise levels. See our AED CPR feedback comparison for which models offer visual feedback.

How many AEDs are needed for a large manufacturing facility?

Plan around a 3-minute retrieval and response target, the AHA's actual published benchmark, rather than a fixed square-footage number.

Multi-level areas, detached buildings and overnight shifts each need their own coverage consideration. Call (855) 286-6384 for a floor-plan-specific recommendation.

What should be included in an industrial AED package?

A rugged AED, alarmed high-visibility cabinet, adult and pediatric pad path, spare battery and pads, a rescue kit, clear signage, and the prescription. See the checklist above.

Does OSHA require AED training for manufacturing employees?

No AED-specific training mandate exists. General Duty Clause exposure and first-aid availability under 1910.151 still apply, and trained responders strengthen your position regardless.

What is the maintenance schedule for factory AEDs?

Check pads and battery on a fixed schedule and after any actual use. Dust, heat and vibration can accelerate wear versus a climate-controlled office.

Exact intervals vary by brand and are listed on each product page.

Planning coverage across production lines, shifts or multiple buildings? Call (855) 286-6384. See all AED value packages or browse AED wall cabinets.

AED Packages for Manufacturing Sites

Noise changes what "audible" means on a production floor

OSHA obligation: no exemption, unlike farms

General Duty Clause

29 CFR 1910.151

No small-facility carve-out

How many AEDs your facility actually needs

What belongs in an industrial AED package

Frequently asked questions

Contact Us

Customer Service

Mailing List

Sign Up for Email

AED Packages for Manufacturing Sites

Products [3]

Noise changes what "audible" means on a production floor

OSHA obligation: no exemption, unlike farms

General Duty Clause

29 CFR 1910.151

No small-facility carve-out

How many AEDs your facility actually needs

What belongs in an industrial AED package

Frequently asked questions